Composite range · construction

Composite rebar for construction

Ribbed and smooth fibreglass rebar from our own production in Podgorica, in diameters from Ø4 to Ø40 mm. It doesn't rust, doesn't conduct electricity and is several times lighter than steel — supplied in 50 and 100 m coils, in bars from 1 to 8 m or cut to length, and on pallets.

Material
Fibreglass
Types
Ribbed and smooth
Supply
Coils, bars, pallets
Diameters
Ø4 – Ø40 mm
Green ribbed composite rebar bars lying side by side, close-up
Ribbed composite rebar

What composite rebar is

Rebar that doesn't rust — so concrete doesn't crack from within.

Composite rebar is a bar made of glass fibres bound with resin. In concrete it does the same job as steel — it takes the tension — but it doesn't corrode.

Steel in concrete that is constantly damp, salted or by the sea rusts over time. Rust takes up more space than the metal, so it breaks up the concrete around it — cracks appear and the concrete cover spalls off. Composite doesn't have that problem. For Montenegro, where much of the building happens by the sea, that is decisive.

  1. Does not corrode

    Moisture, salt and chemicals don't attack the bar. The concrete cover stays intact, and the building needs no rebar repairs.

  2. Several times lighter

    Thinner diameters in coils even fit in a passenger car — no lorry or crane for unloading, and lower transport costs.

  3. Over 1,000 MPa in tension

    That is what the Faculty of Civil Engineering in Belgrade measured on our Ø8 and Ø10 rebar — about twice the yield strength of B500 steel. Test reports

  4. Non-conductive

    A dielectric that doesn't interfere with radio waves, Wi-Fi or sensitive medical equipment — for substations, laboratories and MRI rooms. It also conducts heat far less than steel.

  5. Coils of 50 and 100 m

    Fewer splices and laps than with 6 m steel bars — and less waste on site.

  6. Easy installation

    Cut with an angle grinder or bolt cutters, tied with wire or plastic cable ties. No welding needed.

Where it's used

Concrete exposed to moisture, salt and frost

  • Floor slabs, screeds and industrial floors
  • Paths, pavements, paved areas and open terraces
  • Roads, car parks and driveways
  • Foundations, foundation slabs and retaining walls
  • Seafront buildings and high-humidity areas
  • Tanks and water structures
  • Stone facades and cladding layers
  • Substations and rooms with sensitive electronics

All construction applications

For structural engineers

Where the calculation decides

Composite rebar has a lower modulus of elasticity than steel — under the same load it deflects more. That is why in beams, longer-span slabs and load-bearing elements it is sized by design, to the codes for composite reinforcement (ACI 440, GOST 31938).

The simplest use is where the reinforcement mainly prevents the concrete from cracking: in ground-bearing floors, paths, paved areas, retaining walls and facades. Composite can also be combined with steel rebar in the same structure.

We produce diameters from Ø4 to Ø40 mm, in the lengths the design calls for — and for special projects, to the client's dimensions and technical requirements.

Standards, recommendations and test reports are on the technical documentation page.

How it's installed

The same job as with steel — only lighter

A crew that installs steel rebar can install composite too, with no new tools — just without the welding machine and the lorry for unloading.

  1. 01

    Unloading

    Coils and bundles are carried by hand — no crane or forklift.

  2. 02

    Cutting

    With an angle grinder or bolt cutters, to the length in the design.

  3. 03

    Tying

    With ordinary tie wire or plastic cable ties — no welding.

  4. 04

    Spacers

    The rebar is raised on spacers so that it stays inside the concrete, not under it.

  5. 05

    Concreting

    The usual way — composite doesn't need special concrete.

From production

Made in Podgorica

Rebar from our production — in coils, ready for delivery. Diameters, packaging and prices are in the catalogue.

Coils of 10 mm composite rebar stacked on pallets in front of the warehouse
Ø10 in coilsCoils on pallets in front of the warehouse.
Bundle of green smooth composite rebar bars, close-up
Smooth rebarA bundle of smooth bars cut to length.
Three large coils of composite rebar wrapped in film on pallets
Coils on palletsPrepared for larger projects and continuous deliveries.
Coils of composite rebar for construction wrapped in protective film
Ready for deliveryCoils wrapped in protective film.

Frequently asked questions

What we're asked most often

What lengths of rebar do you supply?

The rebar is supplied in 50 and 100 m coils or in bars from 1 to 8 m, and we cut it to other lengths to order. A coil is up to one metre in diameter. Details are in the catalogue.

How is it cut and tied?

It is cut with an angle grinder or bolt cutters and tied with ordinary tie wire or plastic cable ties. You don't need power on site or cutting discs for a grinder — bolt cutters are enough.

Can it be combined with steel rebar?

Yes — in low-rise and multi-storey construction, composite is combined with steel rebar according to the design.

Why paths, car parks and terraces in particular?

These structures are constantly exposed to moisture, salt and frost. The steel in them corrodes, expands and breaks up the concrete, causing cracks and wear. Composite doesn't corrode, so the concrete stays intact and doesn't need constant repairs.

Is it cheaper than steel?

Per metre, it is generally cheaper than steel rebar of the same load-bearing capacity — and the difference grows once you factor in easier transport, unloading without machinery and faster installation.